The first air conditioners and refrigerators employed toxic or flammable gases, such as ammonia, methyl chloride, or propane, that could result in fatal accidents when they leaked. Thomas Midgley, Jr. created the first non-flammable, non-toxic chlorofluorocarbon gas, Freon, in 1928. The name is a trademark name owned by DuPont for any chlorofluorocarbon (CFC), hydrochlorofluorocarbon (HCFC), or hydrofluorocarbon (HFC) refrigerant. The refrigerant names include a number indicating the molecular composition (e.g., R-11, R-12, R-22, R-134A). The blend most used in direct-expansion home and building comfort cooling is an HCFC known as chlorodifluoromethane (R-22).


Heat pipe heat exchangers or run-around coils perform a similar function when humidity control is required. Two heat exchanger are placed in the air stream, one upstream of the cooling coil and the other downstream of the cooling coil. These heat exchangers are connected together with piping. A heat transfer fluid, whether it be water or refrigerant, is either pumped or gravity fed from one heat exchanger to the other. The heat exchanger down stream of the cooling coil (re-heat coil) cools the liquid medium inside the heat exchanger and heats the air passing over the heat exchanger. The cold liquid inside the heat exchanger is moved to the heat exchanger upstream of the cooling coil (pre-cool coil) where it pre-cools the air passing over the heat exchanger and warms the liquid passing through the heat exchanger. The affect of a heat pipe or run-around coil is to reduce the sensible heat capacity of the AC system. The latent capacity of the AC system increases if direct-expansion equipment is used or remains relatively constant if chilled water equipment is used. Since the sensible capacity of the AC system has been reduced, the system must run longer to meet the thermostat set point thereby removing more moisture.

What happens when you have an emergency? The first reaction of most people is to panic. When a furnace stops working, you need it fixed and fixed immediately—especially in the middle of a cold, Ohio winter. That need can make people feel as if they are at the mercy of the repair company. That is why it is so important to call a company you can trust and rely on—Jennings Heating and Cooling.
A number of other variables can influence your decision on whether to repair or replace your furnace, as well. In addition to cost and brand, consider the expected lifetime of your furnace. If it is more than 15 years old, it might make more sense to invest in a new unit even if it costs more than simply repairing the current problem. Long-term costs also play into the equation. For example, your new furnace may be more energy efficient than the current unit. Even though you will pay more for the actual installation, you might be able to make back your investment through lower energy bills. To make your decision, consult with a reliable professional on what to do. In inspecting your furnace, they will be able to make an informed recommendation that looks not just to the next year, but years into the future. That way, you can make the best possible decision for your home and budget long-term.
Keep your home comfortable all year round with Keep your home comfortable all year round with this high quality and efficient 14 SEER central heating and cooling heat pump system. This system is ideal for new or replacement residential or commercial applications and consists of the outdoor condenser indoor air handler with evaporator coil heat strip and 30 ...  More + Product Details Close

Moncrief provides a wide range of services from high-quality energy-efficient systems, tune-ups and inspections, as well as repairs in the Roswell and Marietta areas. As a full-service heating and cooling company, we stay up-to-date on the most economical and energy-efficient systems available for your home or business. In addition, our technicians are well-trained in a wide range of systems to provide quality and cost-efficient furnace service, repairs and installation.

Installing a split system may involve making modifications to the house itself for the necessary lines to be run. The heat exchangers are also more prone to picking up debris and must be cleaned on a regular basis. While they come with protective screens over the fan, care must still be taken to ensure that nothing gets in, especially in a home with children.
There are a number of claims in the HVAC industry that make HVAC technicians sound like they know what they are doing, but the North American Technician Excellence (NATE) certification program is the only closed book examination and certification program, administered by a third party, that tests real world working knowledge of HVAC systems. That's why all of our service technicians complete and continue NATE certification training throughout their career with SMO.

A packaged system is a single unit combining all the components described in the split system. Since the unit is a package, it must be placed outside the building and indoor air is “ducted” from the building to the packaged system and back through an air distribution system. These units typically have SEER rating from 10 to 18. If heating is required, an alternate method of heating the interior of the building must be used, usually in the form of electric or gas heating.


The liquid refrigerant is returned to another heat exchanger where it is allowed to evaporate, hence the heat exchanger is often called an evaporating coil or evaporator. As the liquid refrigerant evaporates it absorbs energy (heat) from the inside air, returns to the compressor, and repeats the cycle. In the process, heat is absorbed from indoors and transferred outdoors, resulting in cooling of the building.
As a Carrier® dealer, with a wide variety of products to choose from, we can keep your family healthy and feeling comfortable all year long. We carry a complete line of indoor comfort equipment with innovations that raise the standards of comfort and reliability, including air conditioners, heat pumps, gas furnaces, programmable thermostats, humidifiers, ductless split systems, geothermal systems, boilers, air cleaners, ultra violet lights, ventilators and zoning products. Let the experts at Dunes Heating and Air Conditioning, LLC help you customize a solution that's right for you.

When you contract with Vredevoogd Heating & Cooling Grand Rapids MI, you can count on us to make safety our top priority. Your HVAC system is, of course, a major investment and integral to the functioning of your home; however, nothing is as important as the safety of each life within your home. We carefully inspect your system to ensure that it is functioning properly in order to guard against carbon monoxide poisoning or other system emergencies. We take the greatest care when installing your HVAC system, knowing that a perfect installation is the safest installation for your home. We follow our industry’s best practices concerning safety and will happily share our know how with you when it comes to safely maintaining your system between service appointments.  If you ever suspect a problem with your HVAC system, you hear strange noises or smell unpleasant odors, for instance, you can call us night or day, 24/7, to address your heating and cooling emergency. We’ll never leave you in the lurch! We are ready to provide service ASAP to ensure the safe operation of your HVAC system.
HVAC equipment is estimated to last about 15 to 20 years. Yet over the years, parts go out and need to be repaired. Heat sensors, exchangers, and ducts can become worn out. Air conditioning motors may need repairing from time to time. For repairs to your heating and air conditioning systems, and even general maintenance, let HomeAdvisor help. Enter your zip code and let us connect you with prescreened HVAC repair services near you.
In a chilled water system, liquid water is pumped throughout the building to “chilled water coils”. Since the liquid water needs to be at a cold temperature, a “cooling plant” is required. The plant is typically referred to as a chiller plant. Vapor compression equipment in the plant, similar to that described in “How does my AC work”, cool water to a cold temperature and pump the cold water to air-to-water heat exchangers where needed.
A reliable, efficient, and modern cooling system makes everyday life a whole lot better.  Whether you’re in need of new installation, equipment replacement, seasonal maintenance, or repair in Chicagoland and the surrounding suburbs, Air Blue Heating and Cooling Inc. is the right answer.  We bring you quality products and services that result in pure luxury without painful costs.  As a Carrier Factory Authorized Dealer, we specialize in the most recognized, award-winning, and innovative air conditioners on the market.  Along with precision temperature control, take advantage of unprecedented energy efficiency, whisper-quiet sound levels, and a range of features that enable greater control over your environment.  Our team is fully licensed, bonded, insured, and NATE-certified.  We make it easy to get the expert help you need with same-day service/installation, and 24/7 Emergency Service across Wheeling, Buffalo Grove, Northbrook, Deerfield, IL.  When you contact Air Blue Heating and Cooling Inc., we don’t waste your time or money, leave behind mess or damage, or consider our job done until you are 100% satisfied.  With over thirty years of practical experience, we are your local solution to perfect comfort.

In 1992, a non-governmental organization, Greenpeace, was spurred by corporate executive policies and requested that a European lab find substitute refrigerants. This led to two alternatives, one a blend of propane (R290) and isobutane (R600a), and one of pure isobutane.[18][22] Industry resisted change in Europe until 1993, and in the U.S. until 2011, despite some supportive steps in 2004 and 2008 (see Refrigerant Development above).[27][67]

An energy recovery ventilator: This component helps improve the air inside your home by swapping it out with fresh air from the outside. During the winter months when houses are closed up to keep out the cold, the air inside becomes a handy way for colds and flu to infect an entire family. By circulating outside air inside, the health of your family will have a better chance.
Another precaution you can take to prolong the life of your central air unit is to cover it up during winter. Protect it from ice and snow by putting a sheet of plastic or wood on top of the unit. However, only cover the top and not the whole machine. You don't want to trap moisture that could cause it to rust and you don't want to provide a hiding spot for pests.

A dehumidifier is an air-conditioner-like device that controls the humidity of a room or building. It is often employed in basements which have a higher relative humidity because of their lower temperature (and propensity for damp floors and walls). In food retailing establishments, large open chiller cabinets are highly effective at dehumidifying the internal air. Conversely, a humidifier increases the humidity of a building.
An annual inspection of your unit can ensure that the various potential problems mentioned above are detected early, and before they require complete replacement. During this inspection, for instance, a professional might find small cracks in your heat exchanger or a faulty seal in your blower motor. Some manufacturer's warranties even require these annual inspections to maintain validity. Typically, your furnace inspection will cost between $80 and $150 depending on the area in which you live and the professional you work with.

The main problem when installing a multi-split system is the laying of long refrigerant lines for connecting the external unit to the internal ones. While installing a separate split system, workers try to locate both units opposite to each other, where the length of the line is minimal. Installing a multi-split system creates more difficulties, since some of indoor units can be located far from the outside. The first models of multi-split systems had one common control system that did not allow you to set the air conditioning individually for each room. However, now the market has a wide selection of multi-split systems, in which the functional characteristics of indoor units operate separately from each other.
Lennox was started to offer some of the most long-lasting, reliable HVAC systems in the market while providing the best service and quality for customers. Knoechel Heating Company in Zelienople is no different, with our on-going dedication to your comfort and commitment to the community. We strive to be the experts at what we do so you can always be comfortable, and know you can always count on us. Give us a call at 724-452-6280 or arrange an appointment with us so we can help you achieve whole home comfort. 
Because there are so many different potential causes of indoor air quality problems, it is necessary to determine with certainty just what issues you are dealing with in your home. The only way to do so is with the assistance of a qualified professional. Once we discover the source of your IAQ problems, we can go about resolving them with the proper products and services. Call today to enjoy improved indoor air quality in Issaquah, WA.
Service Experts Heating and Air Conditioning was founded with the determination of delivering customers with the most excellent heating and cooling practices in the industry. Since its inception, A-PLUS Service Experts Heating & Air Conditioning in Waldorf has been devoted to our area, offering the first class HVAC (Heating, Ventilation, Air Conditioning) products and services in the area. If you would like to more information about your regional HVAC leaders, simply dial us at 301-747-3140 or set up an appointment with us using our online form.

Tired of dealing with an inoperable furnace? Or, maybe your heating system is only heating half the rooms in your home? Whether you need a new heating system installed or an existing unit repaired, there’s only one name to know—ABC Plumbing, Heating, Cooling & Electric. With more than six decades of experience handling Chicago’s heating problems, our team at ABC has the experience and know-how to get any heating issue diagnosed and resolved quickly and efficiently.
Furnace Circuit Board -- The furnace circuit board controls a variety of functions. It not only handles the regular operation of the furnace, it also monitors the furnace's various safety circuits. Over time, vibrations from the furnace can weaken solder point and cause them to separate. Dirt and debris can cause short-circuits that damage the board. Failure of the circuit board can cause a variety of effects ranging from the fan not turning on to the complete shutdown of the furnace.
Nothing is worse than having your furnace fail on the coldest night of the year. When your furnace needs a repair, you shouldn’t have to worry about the company providing your furnace repair services. You won’t have to – not when you give John Betlem Heating & Cooling a call. No matter what kind of furnace you own, our talented team of technicians are able to easily identify any problem your furnace might be having.

Fuses -- Anyone who has worked with electrical systems knows all about fuses and how they fail. They can burn out over time, may just be loose, or can blow out during an electrical storm or due to overload from another failed component. Of course, that's what they're supposed to do; they stop surges from going through and damaging the rest of the system. When a fuse fails, whatever system it was protecting will stop working.
Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.
Need 24-hour emergency furnace repair? We can provide that too. With our same-day service and live phone and online chat service available 24/7, we make your comfort our top priority. Heating and air conditioning should help you live a comfortable life, so let us help you make your home the most comfortable it has ever been. It’s easy, just grab your furnace repair coupon, then simply give us a call at 615-953-9885, chat or schedule an appointment with us online.

When it comes to heater repair in Denver, a properly serviced system means significant savings for the homeowner. When a Denver heating technician inspects your system before the winter sets in, the first thing they will check is the condition of the air filters. These filters are important, because they are responsible for removing contaminants, allergens, and dust particles from the air every time the system is turned on. When the filters are clogged, expect more particles to easily pass through right into the air you breathe inside the home. The Denver heating experts will inspect and replace any filters that are no longer effective.
A refrigerant leak not only keeps your air conditioner from running efficiently, it's also harmful to the environment. There are many things that can cause your air conditioner to leak coolant, but the usual culprit is a problem with the evaporator coil or outdoor condenser coil. If you discover any freon coming out of your unit, contact a professional. It could be that you need to obtain a patch or a whole new part to resolve the problem.

ISO 16813:2006 is one of the ISO building environment standards.[29] It establishes the general principles of building environment design. It takes into account the need to provide a healthy indoor environment for the occupants as well as the need to protect the environment for future generations and promote collaboration among the various parties involved in building environmental design for sustainability. ISO16813 is applicable to new construction and the retrofit of existing buildings.[30]


Packaged central air conditioner – the name is a good indicator of what to expect from a packaged central air conditioner. The evaporator, compressor, and condenser are all installed in one cabinet.  This cabinet is typically placed on a roof or a concrete slab near the house’s foundation.  Packaged ones normally include electric heating coils or a natural gas furnace, which eliminates the need for a separate furnace inside.
Even if your air conditioning unit is still working, depending on the type of system in your home today, you could recoup your investment in a new system in as little as three years. However, that doesn't mean that your system needs to be replaced. Furnaces, air conditioners, and other heating and cooling systems have made tremendous gains in efficiency over the past five years, so if you have an older unit, it is worth taking a look at whether or not a repair is the best investment.
×