A more efficient method of controlling humidity is to use the waste heat from the refrigeration cycle itself. Instead of rejecting the waste heat outdoors, the heat is directed inside when humidity control is required. One form of heat reclaim is called hot-gas reheat or “refrigerant desuperheating” where refrigerant is passed through a heat exchanger located downstream of the cooling coil. The hot high pressure vapor leaving the compressor passes through this heat exchanger prior to entering the condenser coil. This in turn heats the indoor air and again causes the AC system to run longer to meet the thermostat set point. Although more energy is used, this is much more efficient than turning on an electric heater. Another form of heat reclaim is called sub-cool reheat. This strategy takes the warm liquid refrigerant from the condenser and passes it through a heat exchanger located downstream of the cooling coil. Less heat is available using this method because the majority of the heat has already been rejected at the condenser. Since more energy is used to pump liquid (as opposed to a gas) through the heat exchanger it would appear that this method is less efficient than the hot-gas method, however, the liquid in the heat exchanger is sub-cooled in the cold supply air stream which increases the capacity of the air conditioner. Since more capacity is available, the AC units is able to meet the thermostat more quickly.

As the system carries the cool air through the home, it becomes warmer as it travels through the system.  The air then circulates back to the central air conditioner through the return ducts and registers.  A benefit of a central air conditioner is that it helps dehumidify the incoming air but with extreme humidity, you may have to invest in a dehumidifier to help lower the moisture in the air.  There are also two different types of central air conditioners to choose from.

Feel perfectly comfortable at home with our innovative Lennox Residential heating, cooling and air quality systems. Lennox manufactures high-efficiency HVAC systems including furnaces and air conditioners designed to conserve energy and save money. Our complementing air filtration systems, humidifiers and dehumidifiers help keep indoor air quality healthy and clean.


Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.
With that being said, we ask ourselves, “How do we ensure our customers that we are the company they can count on?”. It all starts with our people. Each of our team members have passed a criminal background and drug test, so you can trust them with your home and family. We are licensed and insured well beyond the minimum requirements set for by the State of Texas. Also, we provide continuous training for both the technical and customer service aspects of our industry. We do this in order to make sure that we are ready and able to serve your needs with excellence.

An air conditioner's compressor contains a refrigerant. As it works, it sends this refrigerant through the system. As warm air blows across the coil that carries this refrigerant, the heat transfers to the refrigerant (cool always absorbs warm). A fan moves the cooled air through the ducting and out of vents that lead into the rooms of your house. The refrigerant returns to the compressor where the absorbed heat is moved outside. The refrigerant is then sent through the coil once again to continue the cycle.

One service an HVAC contractor can provide is a diagnostic test of your heating and central air unit. A reputable technician will examine your unit and ask you questions about various aspects of the system. He or she will check your furnace as well as ductwork and discuss options with you. Beware of a contractor that takes a quick look through your home or place of business and immediately tells you replacing your HVAC system is necessary.

A number of other variables can influence your decision on whether to repair or replace your furnace, as well. In addition to cost and brand, consider the expected lifetime of your furnace. If it is more than 15 years old, it might make more sense to invest in a new unit even if it costs more than simply repairing the current problem. Long-term costs also play into the equation. For example, your new furnace may be more energy efficient than the current unit. Even though you will pay more for the actual installation, you might be able to make back your investment through lower energy bills. To make your decision, consult with a reliable professional on what to do. In inspecting your furnace, they will be able to make an informed recommendation that looks not just to the next year, but years into the future. That way, you can make the best possible decision for your home and budget long-term.


Designed to improve manufacturing process control in a printing plant, Carrier's invention controlled not only temperature but also humidity. Carrier used his knowledge of the heating of objects with steam and reversed the process. Instead of sending air through hot coils, he sent it through cold coils (filled with cold water). The air was cooled, and thereby the amount of moisture in the air could be controlled, which in turn made the humidity in the room controllable. The controlled temperature and humidity helped maintain consistent paper dimensions and ink alignment. Later, Carrier's technology was applied to increase productivity in the workplace, and The Carrier Air Conditioning Company of America was formed to meet rising demand. Over time, air conditioning came to be used to improve comfort in homes and automobiles as well. Residential sales expanded dramatically in the 1950s.[citation needed]

A vapour seal is an essential part of preventing moisture infiltration into or migration out of a critical space, such as a data processing centre or other room that contains sensitive electronic instrumentation.  Essentially, a vapour seal is a barrier that prevents air, moisture, and contaminants from migrating through tiny cracks or pores in the walls, floor, and ceiling into the critical space.  It is also used extensively on pipe insulation to prevent moisture ingress that may cause deterioration of the insulation or freezing in cold conditions.
When you establish routine visits with Vredevoogd Heating & Cooling Grand Rapids MI, you can enhance the longevity of your HVAC system with our custom care. Our technicians are skilled at performing comprehensive inspections. We routinely spot small issues before they can turn into major repairs. By optimally maintaining your system, we can extend its life and ensure that it reliably meets your household’s heating and cooling needs. You can also join our Comfort Club! You can schedule routine appointments to service your system before the hot and cold seasons. If you discover a problem afterward, call us to provide you with immediate service. We can troubleshoot the problem in no time. We’ll give you an upfront estimate concerning cost, parts, and labor. There’s no guessing when it comes to our service and costs. Our techs will provide you with everything you need to know about their service from beginning to end of the job. We even have Financing Available.
Heat pumps are similar to cooling only systems with one exception. A special valve in the refrigeration piping allow the refrigeration cycle to be operated in reverse. A cooling only system cools the indoor air and rejects heat to the outdoors. A heat pump can also cool the indoor air, but when the valve is reversed, the indoor air is heated. A supplementary electric resistance heater may also be used to assist the heat pump at lower outdoor temperatures. In colder climates, heat pumps require a defrost period. During defrost times the electric heater is the only means of heating the interior of the building. These units are manufactured as either split or packaged systems.
A true central air-conditioning system uses ducts to distribute cooled air throughout the house. In a “split system,” the most common design, refrigerant circulates between an indoor coil and a matching—meaning from the same brand—outdoor condenser with compressor (see illustration, below). The refrigerant cools the air, dehumidifying it in the process; a blower circulates air through ducts throughout the house. A thermostat maintains the temperature at the setting you select. A variation is the “heat pump,” a type of system that functions as heater and air conditioner.

In very dry climates, evaporative coolers, sometimes referred to as swamp coolers or desert coolers, are popular for improving coolness during hot weather. An evaporative cooler is a device that draws outside air through a wet pad, such as a large sponge soaked with water. The sensible heat of the incoming air, as measured by a dry bulb thermometer, is reduced. The temperature of the incoming air is reduced, but it is also more humid, so the total heat (sensible heat plus latent heat) is unchanged. Some of the sensible heat of the entering air is converted to latent heat by the evaporation of water in the wet cooler pads. If the entering air is dry enough, the results can be quite substantial.
Excalibur Water Systems helps solve the water challenges around the globe with water solutions for any possible water concerns in: water hardness, filtration of any contaminant, bacteria removal and high purity water needs and also comes with a warranty of up to 20 years at no extra cost. The best warranty for the water treatment equipment industry.
Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.
Need your air conditioning repaired today? Let Dunes Heating and Air Conditioning LLC.  same-day air conditioning repair service come to the rescue. Our air conditioning repair, maintenance and installation technicians and contractors are some of the most highly skilled AC repair technicians in the area. So whether you need your commercial air conditioner repaired or your home air conditioning system replaced, let our team of factory trained and certified home central air conditioning repair technicians be there for you and your family!

A number of other variables can influence your decision on whether to repair or replace your furnace, as well. In addition to cost and brand, consider the expected lifetime of your furnace. If it is more than 15 years old, it might make more sense to invest in a new unit even if it costs more than simply repairing the current problem. Long-term costs also play into the equation. For example, your new furnace may be more energy efficient than the current unit. Even though you will pay more for the actual installation, you might be able to make back your investment through lower energy bills. To make your decision, consult with a reliable professional on what to do. In inspecting your furnace, they will be able to make an informed recommendation that looks not just to the next year, but years into the future. That way, you can make the best possible decision for your home and budget long-term.
Air Blue Heating and Cooling Inc. provides a full range of residential and commercial heating, cooling, and air quality services across Chicagoland and the surrounding suburbs.  With over thirty years of practical experience, we know exactly how to protect your comfort, wallet, and enjoyment of your indoor space.  As a Carrier Factory Authorized Dealer, we ensure top quality products and maximize performance through skilled services.  Our team is fully licensed, bonded, insured, and factory trained.  Every call is answered by a NATE-certified professional, who has verified technical excellence through strenuous, industry-recognized exams.
Most modern air-conditioning systems feature a dehumidification cycle during which the compressor runs while the fan is slowed as much as possible[citation needed] to reduce the evaporator temperature and therefore condense more water. When the temperature falls below a threshold, both the fan and compressor are shut off to mitigate further temperature drops;[clarification needed] this prevents moisture on the evaporator from being blown back into the room.[citation needed] When the temperature rises again,[clarification needed] the compressor restarts and the fan returns to low speed.
A dehumidifier is an air-conditioner-like device that controls the humidity of a room or building. It is often employed in basements which have a higher relative humidity because of their lower temperature (and propensity for damp floors and walls). In food retailing establishments, large open chiller cabinets are highly effective at dehumidifying the internal air. Conversely, a humidifier increases the humidity of a building.
Baker Brothers Air Conditioning company offers residential HVAC services including a/c and air conditioning repair, a/c and air conditioning replacement, a/c and air conditioning installation, a/c and air conditioning tune up, a/c and air conditioning inspections, a/c and air conditioning maintenance on air conditioning units and systems in most or all of the following Dallas, TX ZIP Codes: 75229, 75230, 75225, 75220, 75209, 75219, 75247, 75212, 75235, 75201, 75207, 75248, 75287, 75252, 75244, 75254, 75240, 75251, 75248-1713, 75214, 75228, 75243, 75238, 75218, 75206, 75231, 75204, 75226, 75246, 75227, 75208, 75217, 75232, 75224, 75211, 75241, 75215, 75233, 75253, 75216, 75223, 75237, 75249, 75203, 75210

Energy efficiency can be improved even more in central heating systems by introducing zoned heating. This allows a more granular application of heat, similar to non-central heating systems. Zones are controlled by multiple thermostats. In water heating systems the thermostats control zone valves, and in forced air systems they control zone dampers inside the vents which selectively block the flow of air. In this case, the control system is very critical to maintaining a proper temperature.

When our Denver heating company provides you with maintenance checks before the cold of winter sets in, you will be saving money in several different ways. One of the benefits of a maintenance plan is our technicians will be less likely to have to make repairs throughout the year as long as the system is properly maintained. Our Denver heating company will have your system running at its most efficient, helping to reduce your utility bills each month. An added benefit of a more efficiently running system is the positive environmental effect that it will have.
Although HVAC is executed in individual buildings or other enclosed spaces (like NORAD's underground headquarters), the equipment involved is in some cases an extension of a larger district heating (DH) or district cooling (DC) network, or a combined DHC network. In such cases, the operating and maintenance aspects are simplified and metering becomes necessary to bill for the energy that is consumed, and in some cases energy that is returned to the larger system. For example, at a given time one building may be utilizing chilled water for air conditioning and the warm water it returns may be used in another building for heating, or for the overall heating-portion of the DHC network (likely with energy added to boost the temperature).[4][5][6]
Don’t forget, when you’re in the need for 24 HR emergency repair in Akron, Ohio, Jennings is there for you no matter the time of day or night—24 hours a day and 7 days a week. If you have an emergency, please call 330-784-1286 now. If you would like to request service, please fill out and submit the form below and a Jennings associate will be in touch make an appointment.
Air changes per hour Bake-out Building envelope Convection Dilution Domestic energy consumption Enthalpy Fluid dynamics Gas compressor Heat pump and refrigeration cycle Heat transfer Humidity Infiltration Latent heat Noise control Outgassing Particulates Psychrometrics Sensible heat Stack effect Thermal comfort Thermal destratification Thermal mass Thermodynamics Vapour pressure of water
Buy Home Air Conditioner - We also sell air conditioner equipment like AC condensers and heat pump condensers as well. Need a cased evaporator coil? No problem! Make sure to check out our full lines of trusted air conditioning products – and don't hesitate to contact us with any product-specific questions that may come up during the process of shopping for your new AC.
Non fluorochemical refrigerants, such as ammonia (R717), carbon dioxide (R744) and hydrocarbons such as propane (R290) or isobutene (R600a). These products exist naturally in the environment. Alternative to fluorochemical refrigerants, often used due to their low direct GWP and ODP potential. (However it should be noted that commercial production of natural refrigerants is normally via man-made synthesis).

A hot aisle is a layout design for server racks and other computing equipment in a data centre. Hot aisle data centre design involves lining up server racks in alternating rows with cold air intakes facing one way and hot air exhausts facing the other. The rows the heated exhausts pour into are called hot aisles. See Data Centre Aisle Containment for more information. 

Though forced-air furnaces are normally quite reliable, they can break down. To avoid break downs, it pays to know how to take care of your furnace and fix it when something goes wrong. Inevitably, a furnace stops working when you need it most. Consequently, fixing becomes urgent very quickly. The following instructions will help. With a little do-it-yourself experience and the proper guidance, you can troubleshoot and repair a variety of furnace problems yourself.


R-22 Freon is being phased out & isn't readily available. So the service company may only purchase as needed and the lack of availability would make their cost high. But, as long as they can get it, whatever the cost, unfortunately, is less expensive than replacing the A/C. Which will be the case eventually since it's no longer manufactured or sooner as in my case with a not so old a/c that sprang a leak, that would have been just a repair, but since it uses R-22 the whole unit has to be upgraded(replaced).  

We install heating equipment from Lennox and can repair all major brands, including Carrier, Trane, York, Bryant, Rheem, and many more. We proudly offer same day service and next day installations. Dealing with a heating emergency? We've got you covered! Our team is prepared to assist you 24 hours a day, 7 days a week to ensure that your home remains comfortable and safe for you and your family members.
×