Outdoor Fan Motor -- The outdoor fan, also called the condenser fan, is exposed to external conditions. As such it is most prone to dust and debris and the extreme weather. In desert climates, the outdoor fan motor is subject to heat not only from normal operation but from the outside temperature as well. As it starts to fail, the fan may work fine in the cooler morning hours but stop by afternoon. This can shut down the entire system for hours. When they stop running completely, your air conditioner will no longer work. Running a faulty fan will lead to compressor failure, which is a very costly repair.
An air conditioner's compressor contains a refrigerant. As it works, it sends this refrigerant through the system. As warm air blows across the coil that carries this refrigerant, the heat transfers to the refrigerant (cool always absorbs warm). A fan moves the cooled air through the ducting and out of vents that lead into the rooms of your house. The refrigerant returns to the compressor where the absorbed heat is moved outside. The refrigerant is then sent through the coil once again to continue the cycle.
In very dry climates, evaporative coolers, sometimes referred to as swamp coolers or desert coolers, are popular for improving coolness during hot weather. An evaporative cooler is a device that draws outside air through a wet pad, such as a large sponge soaked with water. The sensible heat of the incoming air, as measured by a dry bulb thermometer, is reduced. The temperature of the incoming air is reduced, but it is also more humid, so the total heat (sensible heat plus latent heat) is unchanged. Some of the sensible heat of the entering air is converted to latent heat by the evaporation of water in the wet cooler pads. If the entering air is dry enough, the results can be quite substantial.
If you need a furnace repaired or an air conditioner serviced, we'll send a local technician out to diagnose the specific problem and recommend solutions for you and your family. There will be a diagnostic fee for the visit, and any specific repairs will be an additional charge. If replacing your system is the best solution, the fee for the diagnosis will be credited toward the purchase and install of a new system.
Air conditioning (often referred to as AC, A/C, or air con)[1] is the process of removing heat and moisture from the interior of an occupied space, to improve the comfort of occupants. Air conditioning can be used in both domestic and commercial environments. This process is most commonly used to achieve a more comfortable interior environment, typically for humans and animals; however, air conditioning is also used to cool/dehumidify rooms filled with heat-producing electronic devices, such as computer servers, power amplifiers, and even to display and store some delicate products, such as artwork.
*Residential Service call's subject to $119.00 travel and diagnostic fee, Commercial Service call's subject to a $149.00 travel and diagnostic fee. Once diagnosed, necessary repairs will be quoted in accordance with standard flat rate repair price. Repair and quoted repair price may be accepted or declined by the customer at that time. Travel and Diagnostic fee will still apply in case customer declines repair. All calls are C.O.D. Overtime rates for Residential Service are $169.00, overtime rates for Commercial services are $179.00.  These rates are for services performed after normal business hours Monday through Friday 8am-4:30pm.
A refrigerant leak not only keeps your air conditioner from running efficiently, it's also harmful to the environment. There are many things that can cause your air conditioner to leak coolant, but the usual culprit is a problem with the evaporator coil or outdoor condenser coil. If you discover any freon coming out of your unit, contact a professional. It could be that you need to obtain a patch or a whole new part to resolve the problem.
SEER is related to the coefficient of performance (COP) commonly used in thermodynamics and also to the Energy Efficiency Ratio (EER). The EER is the efficiency rating for the equipment at a particular pair of external and internal temperatures, while SEER is calculated over a whole range of external temperatures (i.e., the temperature distribution for the geographical location of the SEER test). SEER is unusual in that it is composed of an Imperial unit divided by an SI unit. The COP is a ratio with the same metric units of energy (joules) in both the numerator and denominator. They cancel out, leaving a dimensionless quantity. Formulas for the approximate conversion between SEER and EER or COP are available.[34]

Hello, I too have a Lennox pellet stove, the Eilite mase in 2008. Ours hasn't been professionally cleaned ever. And now it has built up with dust and in the different compartments in the two side panels such as the blowes, motors, and switches. Now when we run it, it will start up and run fine for about 20 minutes and then shuts down. Today I got it to run for 3 hours and then it stopped feeding pellets. I've cleaned out the hooper with a shop vac, vaccummed thoroughly inside the stove, and wiped the visible and reachable dust, but it still isn't working properly. Did you find out any information about your stove. I'm having trouble finding DIY videos for this brand.


In 1758, Benjamin Franklin and John Hadley, a chemistry professor at Cambridge University, conducted an experiment to explore the principle of evaporation as a means to rapidly cool an object. Franklin and Hadley confirmed that evaporation of highly volatile liquids (such as alcohol and ether) could be used to drive down the temperature of an object past the freezing point of water. They conducted their experiment with the bulb of a mercury thermometer as their object and with a bellows used to speed up the evaporation. They lowered the temperature of the thermometer bulb down to −14 °C (7 °F) while the ambient temperature was 18 °C (64 °F). Franklin noted that, soon after they passed the freezing point of water 0 °C (32 °F), a thin film of ice formed on the surface of the thermometer's bulb and that the ice mass was about 6 mm (1⁄4 in) thick when they stopped the experiment upon reaching −14 °C (7 °F). Franklin concluded: "From this experiment one may see the possibility of freezing a man to death on a warm summer's day."[9]

We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?


Here at Brothers Plumbing, Heating, and Electric, we have a Home Care Club that provides members with many benefits. These benefits include: 2 year warranty on all work (drain work is excluded), transferable club membership, no “show up” fees, priority service, 10% discount on repairs, quarterly newsletters, carefree scheduling (we will contact you and remind you when you need service), 2 free furnace/air conditioner filter changes, exclusive coupons, quarterly drawings, 4 on-going safety checks, and a 100% satisfaction guarantee. So if you’d like to join our Home Care Club, then give us a call or click here today.

With that being said, we ask ourselves, “How do we ensure our customers that we are the company they can count on?”. It all starts with our people. Each of our team members have passed a criminal background and drug test, so you can trust them with your home and family. We are licensed and insured well beyond the minimum requirements set for by the State of Texas. Also, we provide continuous training for both the technical and customer service aspects of our industry. We do this in order to make sure that we are ready and able to serve your needs with excellence.


Air conditioner inverter Air door Air filter Air handler Air ionizer Air-mixing plenum Air purifier Air source heat pumps Automatic balancing valve Back boiler Barrier pipe Blast damper Boiler Centrifugal fan Ceramic heater Chiller Condensate pump Condenser Condensing boiler Convection heater Cooling tower Damper Dehumidifier Duct Economizer Electrostatic precipitator Evaporative cooler Evaporator Exhaust hood Expansion tank Fan coil unit Fan heater Fire damper Fireplace Fireplace insert Freeze stat Flue Freon Fume hood Furnace Furnace room Gas compressor Gas heater Gasoline heater Geothermal heat pump Grease duct Grille Ground-coupled heat exchanger Heat exchanger Heat pipe Heat pump Heating film Heating system High efficiency glandless circulating pump High-efficiency particulate air (HEPA) High pressure cut off switch Humidifier Infrared heater Inverter compressor Kerosene heater Louver Mechanical fan Mechanical room Oil heater Packaged terminal air conditioner Plenum space Pressurisation ductwork Process duct work Radiator Radiator reflector Recuperator Refrigerant Register Reversing valve Run-around coil Scroll compressor Solar chimney Solar-assisted heat pump Space heater Smoke exhaust ductwork Thermal expansion valve Thermal wheel Thermosiphon Thermostatic radiator valve Trickle vent Trombe wall Turning vanes Ultra-low particulate air (ULPA) Whole-house fan Windcatcher Wood-burning stove
You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.

The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.


As a Carrier Factory Authorized Dealer and President’s award winner, we specialize in world-recognized, award-winning, and technologically advanced heating, cooling and air quality products. From air conditioning and heat pumps to furnaces and boilers, you’re going to benefit from increased energy efficiency, decreased sound levels and innovative features that make everyday life easier, more enjoyable and far more comfortable. We provide FREE estimates and flexible financing opportunities. Our goal is to maximize value, sustainability and long-term customer satisfaction.
We maintain a complaint-free A+ rating with the Better Business Bureau, and are a 2017 Better Business Award Winner for ethics. Comfort Plus Services has achieved recognition as a Carrier Factory Authorized Dealer for sound business practices, technical expertise, and customer approval ratings. We simplify the demands of local weather and a comfortable home with upfront pricing, honest estimates, comprehensive service plans, and Emergency Service throughout Salisbury, Fruitland, Delmar, Hebron, Eden, Delmar, Parsonsburg, Pittsville, Mardela Springs, Princess Anne & Willards, MD and more. See our Areas of Service. For new home comfort systems, Comfort Plus Services protects your interests with a 100% money back guarantee. We provide expert service you can trust.

American design standards are legislated in the Uniform Mechanical Code or International Mechanical Code. In certain states, counties, or cities, either of these codes may be adopted and amended via various legislative processes. These codes are updated and published by the International Association of Plumbing and Mechanical Officials (IAPMO) or the International Code Council (ICC) respectively, on a 3-year code development cycle. Typically, local building permit departments are charged with enforcement of these standards on private and certain public properties.
Refrigerant 22 (R-22 or MonoChloroDiFlouroMethane, CHClF2) is one of the most common refrigerants and is used in a wide variety of applications such as refrigeration, aerosol propellants, cleaning solvents, and foaming agents for plastics. This refrigerant is believed to be partially responsible for damaging the earth’s ozone layer and it’s use is being phased out over the next two decades. The ozone layer is a result of sunlight reacting with oxygen to produce a layer in the stratosphere more than 10 km above the earth’s surface. As R-22 refrigerant escapes from an AC system through leaks or is released into the atmosphere by other means, the R-22 molecule containing the chlorine atom (“monochloro”) rises in the atmosphere. Sunlight breaks down the R-22 molecule to yield a free chlorine radical (Cl-). The free chlorine radical combines with ozone (O3), decomposing it into normal oxygen (O2).
Energy efficiency can be improved even more in central heating systems by introducing zoned heating. This allows a more granular application of heat, similar to non-central heating systems. Zones are controlled by multiple thermostats. In water heating systems the thermostats control zone valves, and in forced air systems they control zone dampers inside the vents which selectively block the flow of air. In this case, the control system is very critical to maintaining a proper temperature.
Packaged terminal heat pumps (PTHP) are are similar to a window-mounted air conditioner. These units are typically installed in a sleeve passing through the outdoor wall of an apartment, hotel, school classroom, etc. PTHPs are completely self contained and require only an electrical connection in addition to the opening in the building shell. They use the outdoor air as the heat source in winter and as a heat sink in summer. They also can provide ventilation air. Flexibility and lower installed cost are the primary advantages of the PTHP. Disadvantages include in-room maintenance, higher operating cost, relatively short life, imprecise "on-off" temperature control, and they can be rather noisy.
The HVAC industry is a worldwide enterprise, with roles including operation and maintenance, system design and construction, equipment manufacturing and sales, and in education and research. The HVAC industry was historically regulated by the manufacturers of HVAC equipment, but regulating and standards organizations such as HARDI, ASHRAE, SMACNA, ACCA, Uniform Mechanical Code, International Mechanical Code, and AMCA have been established to support the industry and encourage high standards and achievement.
There are a number of claims in the HVAC industry that make HVAC technicians sound like they know what they are doing, but the North American Technician Excellence (NATE) certification program is the only closed book examination and certification program, administered by a third party, that tests real world working knowledge of HVAC systems. That's why all of our service technicians complete and continue NATE certification training throughout their career with SMO.
SEER is useful for comparing one model to another much in the same way that a car's calculate MPG is useful. It's not an accurate prediction of exactly how efficient the system is, but it can tell you which one is more efficient. Also, since SEER is based on a "cooling season", what region you live in will determine how long or short your cooling season is.
Put simply, any home that uses air pushed through ductwork for heating purposes takes advantage of forced air heating. In other words, this term refers not to your furnace, but to the delivery method of the heat throughout your home. Forced air heating is possible with electric or gas furnaces, or a heat pump. Any issues with this delivery system that aren't directly related to the furnace likely have to do with the duct work, which costs between $35 and $55 per linear square foot to repair, or the air handling unit.

Need your air conditioning repaired today? Let Dunes Heating and Air Conditioning LLC.  same-day air conditioning repair service come to the rescue. Our air conditioning repair, maintenance and installation technicians and contractors are some of the most highly skilled AC repair technicians in the area. So whether you need your commercial air conditioner repaired or your home air conditioning system replaced, let our team of factory trained and certified home central air conditioning repair technicians be there for you and your family!
AC units and thermostats have built-in delay features when they’re shut down and then repowered. The delay can be as long as 10 minutes. And, if you’ve subscribed to an energy-saving device from your local power utility, the unit can take even longer to reset. If you’ve installed the parts shown and reinstalled the disconnect block, repowered the circuit breaker, turned on the switch at the furnace, moved the thermostat to AC mode and lowered the temperature below the indoor temperature, and the unit doesn’t fire up after 30 minutes, it’s time to call a pro.
Heil HVAC is another one of the best air conditioner brands that doesn’t get as much love as they should. This AC brand’s tech allows different heating and cooling components  send information and synchronize performance, becoming more energy efficient and reliable overall. Heil AC products can achieve up to a 97% efficiency rating and SEER figures of 19. They also come with comprehensive 10 year warranties.
Electronically Commutated (EC) fans use brushless DC motors which include in-built electronics to convert the AC supply to DC without the need for a separate DC supply. EC fans provide a more efficient (up to 30%) means of airflow through Precision Air Conditioning (PAC) units with the additional benefit of variable speed control via an output signal from the unit controller. Also see EC Fan upgrades.
In very dry climates, evaporative coolers, sometimes referred to as swamp coolers or desert coolers, are popular for improving coolness during hot weather. An evaporative cooler is a device that draws outside air through a wet pad, such as a large sponge soaked with water. The sensible heat of the incoming air, as measured by a dry bulb thermometer, is reduced. The temperature of the incoming air is reduced, but it is also more humid, so the total heat (sensible heat plus latent heat) is unchanged. Some of the sensible heat of the entering air is converted to latent heat by the evaporation of water in the wet cooler pads. If the entering air is dry enough, the results can be quite substantial.
A pinging or popping sound coming from the duct work can come from thermal expansion—the ductwork expanding and contracting as it heats and cools.  Or, air blowing past a loose flap of metal can make the sound. Track along the duct runs, listening for the sound. If you locate it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.

In 1902, the first modern electrical air conditioning unit was invented by Willis Carrier in Buffalo, New York.[citation needed] After graduating from Cornell University, Carrier found a job at the Buffalo Forge Company. There, he began experimenting with air conditioning as a way to solve an application problem for the Sackett-Wilhelms Lithographing and Publishing Company in Brooklyn, New York. The first air conditioner, designed and built in Buffalo by Carrier, began working on 17 July 1902.[citation needed]
Here at Brothers Plumbing, Heating, and Electric, we have a Home Care Club that provides members with many benefits. These benefits include: 2 year warranty on all work (drain work is excluded), transferable club membership, no “show up” fees, priority service, 10% discount on repairs, quarterly newsletters, carefree scheduling (we will contact you and remind you when you need service), 2 free furnace/air conditioner filter changes, exclusive coupons, quarterly drawings, 4 on-going safety checks, and a 100% satisfaction guarantee. So if you’d like to join our Home Care Club, then give us a call or click here today.

Modern air conditioning systems are not designed to draw air into the room from the outside, they only recirculate the increasingly cool air on the inside. Because this inside air always has some amount of moisture suspended in it, the cooling portion of the process always causes ambient warm water vapor to condense on the cooling coils and to drip from them down onto a catch tray at the bottom of the unit from which it must then be routed outside, usually through a drain hole. As this moisture has no dissolved minerals in it, it will not cause mineral buildup on the coils. This will happen even if the ambient humidity level is low. If ice begins to form on the evaporative fins, it will reduce circulation efficiency and cause the development of more ice, etc. A clean and strong circulatory fan can help prevent this, as will raising the target cool temperature of the unit's thermostat to a point that the compressor is allowed to turn off occasionally. A failing thermistor may also cause this problem. Refrigerators without a defrost cycle may have this same issue. Dust can also cause the fins to begin blocking air flow with the same undesirable result: ice.
Its unique feature is the presence of one main external unit that connected to several indoor units. Such systems might be the right solution for maintaining the microclimate in several offices, shops, large living spaces. Just few of outdoor units do not worsen the aesthetic appearance of the building.The main external unit can be connected to several different indoor types: floor, ceiling, cassette, etc.

A specialized air conditioner that is used only for dehumidifying is called a dehumidifier. It also uses a refrigeration cycle, but differs from a standard air conditioner in that both the evaporator and the condenser are placed in the same air path. A standard air conditioner transfers heat energy out of the room because its condenser coil releases heat outside. However, since all components of the dehumidifier are in the same room, no heat energy is removed. Instead, the electric power consumed by the dehumidifier remains in the room as heat, so the room is actually heated, just as by an electric heater that draws the same amount of power.
A dehumidifier is an air-conditioner-like device that controls the humidity of a room or building. It is often employed in basements which have a higher relative humidity because of their lower temperature (and propensity for damp floors and walls). In food retailing establishments, large open chiller cabinets are highly effective at dehumidifying the internal air. Conversely, a humidifier increases the humidity of a building.
It’s important to keep your furnace receives regular maintenance to ensure that it’s working properly and efficiently. Routine maintenance can also extend the life of your heating system by several years. Ask about our annual maintenance agreements that cover your plumbing, heating, and cooling systems and save you money. A furnace that has been neglected may be working too hard, which can result in inconsistent air temperatures in your Minneapolis area home. Learn more about the importance of routine maintenance on your HVAC system.
An electric furnace provides warmth by moving air over and through a series of coils. Ductwork and vents then distribute that air to the individual rooms in your home. Repair costs will depend on both the brand and the exact nature of the problem, but tend to be lower than some of the options above. That's because the units are small, and issues tend to be contained within the heating elements themselves. Expect to spend less than $300 on your electric furnace repair, depending on the exact problem.
Looking for a local and trusted air conditioning and heater expert that is nearby? HVACs Today is here to help. Keeping your home or business heated or cooled is what we are great at. From installation to replacement and repairs, our technicians can complete your job quickly and correctly. Skilled contractors can solve your HVAC needs: no problem is too big or too small. Call us today to schedule your heating and cooling service.

Heating Repair Company

×